This is a high-speed linear actuator with a 50mm stroke, featuring a high-speed DC motor and a tubular design. It boasts high speed capabilities, with a maximum speed of 230 mm/s and a thrust of 50 N (10 lbs). With an IP rating of IP54, it is suitable for indoor micro-applications.
Key Features:
- High-quality products and high-quality services
- Metal housing, able to work in very harsh environments
- High strength wear-resistant gear
- Aluminum alloy telescopic tube and outer tube, good corrosion resistant
- Strong thrust, up to 200 N / 20 kg / 40 lbs
- Multiple speed options, from 45 mm/second to 230 mm/second
- Multiple stroke options, from 50 mm to 600 mm, any stroke within this range can be customized (e.g. 225mm, 370mm, 550mm)
- Advanced waterproof and dustproof technology
- Low power consumption and low noise
- Built-in two limit switches, linear actuator will automatically stop when stroke rod reaches the limit position.
- Built-in Hall sensor is optional, so you can use the synchronous controller to operate 2, 4 or more linear actuators fully synchronously
- With auto-locking capability to hold load position after stopping, and no power supply is required
- Maintenance-free
Application
Mainly used for doors, windows, cellars, trapdoors, solar tracking
system, medical devices, agricultural machinery, vehicles, ships,
elevator platforms, lifting tables, TV lifts, robots, cabinetries,
massage sofas, electric beds, medical chairs and other electrical
equipment. It can open, close, push, pull, lift and descend these
devices.
It can replace hydraulic and pneumatic products to save power
consumption.
Operation
When linear actuator is connected to DC power supply, the stroke rod
will extend outward; after switching the power in the reverse direction,
the stroke rod will retract inward.
The direction of movement of the stroke rod can be changed by switching
the polarity of DC power supply.
Stroke and Length (Model 0041561)
| Parameter | Value |
|---|---|
| Stroke | 50mm |
| Retraction Length | 285mm (center distance between two mounting holes when the linear actuator is fully retracted) |
| Extension Length | 335mm (center distance between two mounting holes when the linear actuator is fully extended) |
The linear actuator has two built-in limit switches, When the linear
actuator is fully retracted or fully extended, it will stop
automatically.
We can adjust the position of the built-in limit switches during
production to meet customer-specified stroke and retraction lengths.
Note 1: The specified stroke must be less than the standard stroke of the ordered actuator. For example, a specified stroke of 40 mm is less than the standard stroke of the ordered actuator (50 mm). In this case, the retraction length will be reduced by an equivalent value, resulting in a retraction length of 275 mm. Of course, you can also choose to retain the original standard retraction length of 285 mm.
Note 2: The specified retraction length must be less than the standard retraction length of the ordered actuator. For example, a specified retraction length of 270 mm is less than the standard retraction length of the ordered actuator (285 mm). In this case, the stroke must also be reduced by an equivalent value, resulting in an effective stroke of 35 mm.
Product Specifications
| Parameter | Value |
|---|---|
| Working Voltage | DC 12V or DC 24V (24V most commonly used) |
| Stroke | 2 inches / 50 mm |
| Optional Speed (No-load) | 45±5mm/s, 80±10mm/s, 140±15mm/s, 230±25mm/s (The actual working speed will gradually slow down as the load increases.) |
| Max Load Capacity | 200 N / 20 kg / 40 lbs at 45mm/s (Linear actuator can get maximum load capacity when it operates in the vertical direction, and the pulling force is less than pushing force.) |
| No-load Current | about 1.5A |
| Full Load Current | about 3-6A |
| Recommended Power Supply |
1 actuator: 12V/10A or 24V/5A 2 actuators: 12V/20A or 24V/10A 3~4 actuators: 12V/50A or 24V/25A |
| Outer Tube Dameter | 55mm [2.2 in] |
| Shaft Diameter | 28mm [1.1 in] |
| Front / Rear Connector Mounting Hole Diameter | 8mm [0.315 in] |
| Housing Material | Aluminum Alloy |
| Stroke Rod Material | Aluminum Alloy |
| Gear Material | Polymer Plastic |
| Motor Type | Brushed DC Motor |
| Duty Cycle | 20%, Max 2mins continuous use |
| Service Life | approx. 25,000 cycles |
| Power Cable | Ordinary two-core wire / Six-core wire (with built-in Hall sensors) |
| Normal Linear Actuator Cable Length | 1000±10%mm [40 in] (The length can also be customized according to your specific needs) |
| Certifications | CE |
| Environment Temperature | -26℃ to 85℃ |
| Operating Noise | about 46dB~52dB (Linear actuators with different parameters will have different noise levels.) |
| IP Rating | IP54, not suitable for outdoor use |
Different Speeds and Corresponding Maximum Thrust
| No-load Speed | Maximum Thrust |
|---|---|
| 45mm/s | 200 N / 20 kg / 40 lbs |
| 80mm/s | 130 N / 13 kg / 30 lbs |
| 140mm/s | 100 N / 10 kg / 20 lbs |
| 230mm/s | 50 N / 5 kg / 10 lbs |
Note:
1. The above data is the maximum load capacity that can be obtained when the linear actuator runs in the vertical direction. If the weight of your equipment (such as a cellar door) is 100kg, and you want to use a linear actuator to open this door, you need to calculate the actual force acting on the linear actuator according to your installation method. This force is usually 2-5 times the weight of the cellar door. If you don't know how to calculate it, please contact us for help.
2. The above is the speed at no load, and the actual working speed will gradually slow down as the load increases. Full load speed is approximately 60-70% of No-load speed.
3. Different speeds correspond to different maximum loads. Please select the right speed according to the speed and maximum load you need.
4. Linear actuators are not recommended for continuous operation under maximum load, we recommend letting it work at about half of the maximum load to get a longer working life.
5. The maximum pull force of the linear actuator is slightly less than its maximum thrust force.
Fixed Bracket and Control Accessories
1. This linear actuator does not contain fixed mounting brackets, please click here to purchase. (Each linear actuator would require two mounting brackets, one to fix the head of linear actuator and another to fix the bottom of linear actuator.)
2. Compatible Mounting Brackets: Bracket E for the head or the bottom, Bracket A or Bracket C for the bottom.
3. If you need a power supply to power linear actuator, please click here to purchase.
4. If you want to use external limit switches to stop linear actuator at any position, please click here to purchase.
5. If you want to use a manual switch to operate linear actuator, please click here to purchase.
6. If you want to use a remote control switch to operate linear actuator wirelessly, please click here to purchase.
7. If you want to control 2, 4 or more linear actuators fully synchronously, you need to purchase built-in Hall effect sensors for each linear actuator, and buy a synchronization controller, please click here to purchase.
Production Time & Return or Exchange Policy
The linear actuators are customized and not in stock, and we need to spend 9~12 working days to produce them according to the specified parameters in your order, so that we don't accept returns or cancel orders. If customers order unsuitable linear actuators themselves, we also do not accept exchanges, please understand.
Import Customs Duty Explanation
1. Our store will offer one or two different shipping methods depending on the actual situation of the order. Since we ship from Hong Kong, China to worldwide, import duties will be incurred on the package regardless of which shipping method the customer chooses.
2. For small or lightweight packages, we will select a suitable freight company so that we can pay the import duties on the customer's behalf at the time of shipment. Therefore, the customer will not need to pay any import duties or taxes upon receiving the package.
3. For large or heavy packages, regardless of the freight company we choose, customs will collect import duties and taxes directly from the customer upon customs clearance or upon receipt of the package. The duty amount is usually 20% of the order amount (excluding shipping costs).
4. If the customer wishes us to pay the import duties on the customer's behalf, please contact us when placing the order and pay an additional 20% of the order amount as prepaid duties. We will then pay the duties for the customer.
5. If the customer chooses to pay the import duties themselves, please
contact us after paying the duties and receiving the package. We will
provide the customer with a discount voucher of a certain amount, which
can be used for their next purchase. The discount amount will be the
lesser of the import duties actually paid by the customer and 20% of the
original order amount (excluding shipping costs).
Please note: We cannot refund cash for import duties paid by the customer themselves. Thank you for your understanding.
6. When the transport company or the customs informs the customer to pay the import duties, if the customer doesn't agree to pay, the package will be returned or destroyed, and the customer will need to bear all responsibility and cost.